A BEGINNER'S GUIDE TO INSTALLING A BATHTUB

A Beginner's Guide to Installing a Bathtub

A Beginner's Guide to Installing a Bathtub

Blog Article

Click Here

Listed here down the page you can find more professional insight related to How to Install a Bathtub Yourself.


How to Install a Bathtub
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and often, tiling skills. Changing an old bath tub with a new one is also a reasonably hard project. If the old bathtub is readily obtainable, the project can relocate immediately; if you have to open a wall to eliminate the old bathtub and also position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and also embeded in the brand-new one. Make sure you have actually qualified yourself for the task as well as are comfortable attempting it. As opposed to hiring a contractor to take control of a halfway-completed job, it is far better to consider using one prior to you begin. Opportunities are you might require a professional plumber to make tube connections.
This post will assist you set up a brand-new bathtub in your washroom if you have already acquired a brand-new tub and don't need to transform the setup of your previous supply of water pipes.
Your devices and also material checklist should consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be rather bothersome due to the restricted accessibility that is often the instance.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the remaining water that will come from the pipes. As soon as the supply pipes have been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing compound.
    Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.

    Suitable New Touches


    If the tails of the new faucets are plastic, then you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the existent supply pipes.
    If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next off, position the tap in the mounting hole in the bath/basin making certain that the washers remain in location in between the faucet and also the sink. Protect the faucet in position with the producer offered backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former kind should be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.

    Installing the Bath tub


    Making use of the two wooden boards under its feet, place the bathtub in the required setting. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
    The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub until the spirit level reads level.
    To mount faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
    Activate the supply of water and check all joints as well as new pipework for leakages as well as tighten them if needed. Load the bathtub and also inspect the overflow outlet and the regular electrical outlet for leakages.
    Lastly, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the tub ought to wait till the tub has been utilized at the very least once as this will certainly resolve it into its last position.

    Getting ready for the Installation


    To start with, the supporting frame supplied with the bathroom ought to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop strain on the bath tub.
    Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washing machines.
    Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final setting.

    Tiling Around the Bathtub


    In the area where the bathroom meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in complications with moisture and also possible leaks to the ceiling below.
    You can select from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, as well as are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in usage. The sealant can crack fairly early if you do not consider this activity prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently offered on the market. It is a good idea to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We had been guided to that write-up on Tools You Need to Install a New Bathtub from an acquaintance on another website. Are you aware of somebody else who is inquisitive about A Step-by-Step Guide to Installing a Bathtub? Be sure share it. Thank-you for going through it.


    Top-notch service? Dial here.

    Report this page